I am pulling the trigger and rolling my own FreeNAS box. After reading tons of hardware configurations and recommendations I've settled on some hardware that looks like this:
NORCO CHASSIS - RPC-4020
CORSAIR HX850W 850w POWER SUPPLY
SUPERMICRO MOTHERBOARD C2SEA
INTEL CELERON E3400 2.6G CPU
4GB RAM
ADAPTEC 6805 SATA III RAID CONTROLLER KIT
10 x 2TB 7200 RPM, SATA 6G, 64MB CACHE SEAGATE BARRACUDA XT HARD DRIVE
(I will add a SAS expander and another 12 drives in the near future)
Hardware has been purchased, delivered and assembled. FreeNAS USB stick created. Unfortunately, FreeNAS won't pickup my Adaptec RAID 6805 controller.
Given that FreeNAS is built on FreeBSD and I can download drivers from Adaptec for that platform, can anyone give me some guidance on how to successfully apply/install this driver?
Apprecaite the help.
Some time ago, we changed the hardware of our VM server. We replaced the RAID controller with an Adaptec 6805 because the old controller had some problems. The server run with ESXi 5.1.
The problem with our Adaptec controller was that ESXi didn't support it out-of-the-box. It was supported in general but the driver was not included. We thought that the new ESXi 6 could contain the driver, but it didn't. So we had to create our own ESXi image with the Adaptec driver.
We thought it shouldn't be a problem because there was much documentation about custom images:
The package provides the Adaptec SAS Enclosure installation files for Adaptec RAID controllers. These drivers are Microsoft Certified for: - Adaptec RAID 6805E using Firmware/BIOS b19176. Important Notes - During the installation of this file, be sure that you are logged in as the Administrator or as a user with Administrative rights. Download Adaptec controller drivers or install DriverPack Solution software for driver scan and update. Adaptec RAID 6805/6805Q. Adaptec RAID 6805E. ADAPTEC 6805 SATA III RAID CONTROLLER KIT 10 x 2TB 7200 RPM, SATA 6G, 64MB CACHE SEAGATE BARRACUDA XT HARD DRIVE (I will add a SAS expander and another 12 drives in the near future) Hardware has been purchased, delivered and assembled. FreeNAS USB stick created. Unfortunately, FreeNAS won't pickup my Adaptec RAID 6805 controller. Home Support RAID Adaptec RAID 6805 Adaptec RAID 6805 8 internal port, low profile, SAS 2.0 and Gen 2 PCI-Express (PCIe) Unified Serial RAID controller with Zero-Maintenance Cache Protection and Intelligent Power Management delivers exceptional performance, advanced data protection, maximum scalability and the lowest total cost of ownership for.
https://blogs.vmware.com/vsphere/2012/04/using-the-vsphere-esxi-image-builder-cli.html
http://www.virten.net/2015/03/esxi-6-0-image-for-intel-nuc/
(DE) https://www.thomas- krenn.com/de/wiki/Individuelles_ESXi_5....
Some problems:
- We tried to create an image for version 6
- We used the free version of ESXi with all its limitations
A problem was that the documentation references an 'offline software depot'. You can download the offline depot for the paid version but it's not available for the free version - not as simple download. No offline deplot means no custom image - right? Not right, because it's also possible to use an online depot.
The problem was that the documentation didn't contain a full description. We found some hints in different blogs but no complete description.
Adaptec Raid 6805/6805q Driver Downloads
Here are the steps how we created our custom ESXi 6 image with Adaptec 6805 driver:
Downloads
- ESXi
- PowerCLI 6
- Adaptec driver
Adaptec Raid 6805/6805q Driver Usb
Useful PowerCLI Documentation:
https://pubs.vmware.com/vsphere-55/index.jsp#...ve-EsxSoftwarePackage.html
Adaptec Raid 6805/6805q Driver Win 10
Image creation
Adaptec Raid 6805/6805q Driver Download
- Install PowerCLI 6 (and all required dependencies)
- Unzip the Adaptec driver to e.g. C:tempVMServer6
- Run PowerCLI as Administrator (sometimes, first launch of PowerCLI isn't working - simply close/run again)
- Execute following commands# Preconfigure
Set-ExecutionPolicy RemoteSigned
cd c:tempVMServer6# Use online depot
Add-EsxSoftwareDepot https://hostupdate.vmware.com/software/VUM/PRODUCTION/main/vmw-depot-index.xml
# Add offline bundle for adaptec driver
Add-EsxSoftwareDepot aacraid-6.0.6.2.1.41024-offline_bundle-2915492.zip# Check added depots
$DefaultSoftwareDepots# Lists all ESXi-6.* profiles
Get-EsxImageProfile -Name'ESXi-6.*'# Sets the base profile
New-EsxImageProfile -CloneProfile'ESXi-6.0.0-20160104001-standard'-name'ESXi-6.0.0-20160104001-standard-Adaptec'-Vendor'rjahn@SIB'-AcceptanceLevel'CommunitySupported'# Lists all included drivers
Get-EsxSoftwarePackage -Name'*aacraid*'# Adds adaptec driver from offline bundle
Add-EsxSoftwarePackage -ImageProfile'ESXi-6.0.0-20160104001-standard-Adaptec'-SoftwarePackage scsi-aacraid# Creates boot image
Export-ESXImageProfile -ImageProfile'ESXi-6.0.0-20160104001-standard-Adaptec'-ExportToISO-filepath C:tempVMServer6buildESXi-6.0.0-20160104001-standard-Adaptec.iso# Creates Bundle
Export-ESXImageProfile -ImageProfile'ESXi-6.0.0-20160104001-standard-Adaptec'-ExportToBundle-filepath C:tempVMServer6buildESXi-6.0.0-20160104001-standard-Adaptec.zip
Version numbers may be different, but the procedure should work for you as well. The online depot:
https://hostupdate.vmware.com/software/VUM/PRODUCTION/main/vmw-depot-index.xml
Adaptec Raid 6805/6805q Driver Updater
was the most important thing. All other steps can be found in the standard documentation.